// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
//#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
//#if F_CPU == 8000000L
//#define MY_BAUD_RATE 38400
//#endif

// Flash leds on rx/tx/err
// #define MY_LEDS_BLINKING_FEATURE
// Set blinking period
// #define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
// #define MY_WITH_LEDS_BLINKING_INVERSE

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN 3

// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN 5 // the PCB, on board LED

#include <SPI.h>
#include <MySensors.h>  
#include <Bounce2.h>

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#define RELAY_1 22 // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define RELAY_2 23
#define RELAY_3 24
#define RELAY_4 25
#define RELAY_5 26
#define RELAY_6 27
#define RELAY_7 28
#define RELAY_8 29
#define RELAY_9 30
#define RELAY_10 31
#define RELAY_11 32
#define RELAY_12 33
#define RELAY_13 34
#define RELAY_14 35
#define RELAY_15 36
#define RELAY_16 37
#define RELAY_17 38
#define RELAY_18 39
#define RELAY_19 40
#define RELAY_20 41
#define RELAY_21 42
#define RELAY_22 43
#define RELAY_23 44
#define RELAY_24 45
#define RELAY_25 46
#define RELAY_26 47
#define RELAY_27 48
#define RELAY_28 49
#define RELAY_29 50
#define RELAY_30 51
#define RELAY_31 52
#define RELAY_32 53

#define NUMBER_OF_RELAYS 32 // Total number of attached relays
#define RELAY_ON 1 // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

#define BUTTON1_PIN A0 // stan wysoki!
#define BUTTON2_PIN A1
#define BUTTON3_PIN A2
#define BUTTON4_PIN A3
#define BUTTON5_PIN A3
#define BUTTON6_PIN 8
#define BUTTON7_PIN 9
#define BUTTON8_PIN 10
#define BUTTON9_PIN 11
#define BUTTON10_PIN 12

void before() {
  for (int sensor = 1, pin = RELAY_1; sensor <= NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor) ? RELAY_ON : RELAY_OFF);
  }
}
Bounce debouncer1 = Bounce();
Bounce debouncer2 = Bounce();
Bounce debouncer3 = Bounce();
Bounce debouncer4 = Bounce();
Bounce debouncer5 = Bounce();
Bounce debouncer6 = Bounce();
Bounce debouncer7 = Bounce();
Bounce debouncer8 = Bounce();
Bounce debouncer9 = Bounce();
Bounce debouncer10 = Bounce();

void setup() {
  // Setup locally attached sensors
  delay(10000);
  // Setup the button.
  pinMode(BUTTON1_PIN, INPUT);
  pinMode(BUTTON2_PIN, INPUT_PULLUP);
  pinMode(BUTTON3_PIN, INPUT_PULLUP);
  pinMode(BUTTON4_PIN, INPUT_PULLUP);
  pinMode(BUTTON5_PIN, INPUT_PULLUP);
  pinMode(BUTTON6_PIN, INPUT_PULLUP);
  pinMode(BUTTON7_PIN, INPUT_PULLUP);
  pinMode(BUTTON8_PIN, INPUT_PULLUP);
  pinMode(BUTTON9_PIN, INPUT_PULLUP);
  pinMode(BUTTON10_PIN, INPUT_PULLUP);
    
  // After setting up the button, setup debouncer.
  debouncer1.attach(BUTTON1_PIN);
    debouncer1.interval(5);
  debouncer2.attach(BUTTON2_PIN);
    debouncer2.interval(5);
  debouncer3.attach(BUTTON3_PIN);
    debouncer3.interval(5);
  debouncer4.attach(BUTTON4_PIN);
    debouncer4.interval(5);
  debouncer5.attach(BUTTON5_PIN);
    debouncer5.interval(5);
  debouncer6.attach(BUTTON6_PIN);
    debouncer6.interval(5);
  debouncer7.attach(BUTTON7_PIN);
    debouncer7.interval(5);
  debouncer8.attach(BUTTON8_PIN);
    debouncer8.interval(5);
  debouncer9.attach(BUTTON9_PIN);
    debouncer9.interval(5);
  debouncer10.attach(BUTTON10_PIN);
    debouncer10.interval(5);
}

void presentation(){
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Przekazniki_1", "1.0");

  for (int sensor = 1, pin = RELAY_1; sensor <= NUMBER_OF_RELAYS; sensor++, pin++) {
    // Register all sensors to gw (they will be created as child devices)
    present(sensor, S_LIGHT);
  }
}

MyMessage msg1(1, V_LIGHT);
MyMessage msg2(2, V_LIGHT);
MyMessage msg3(3, V_LIGHT);
MyMessage msg4(4, V_LIGHT);
MyMessage msg5(5, V_LIGHT);
MyMessage msg6(6, V_LIGHT);
MyMessage msg7(7, V_LIGHT);
MyMessage msg8(8, V_LIGHT);
MyMessage msg9(9, V_LIGHT);
MyMessage msg10(10, V_LIGHT);
MyMessage msg11(11, V_LIGHT);
MyMessage msg12(12, V_LIGHT);
MyMessage msg13(13, V_LIGHT);
MyMessage msg14(14, V_LIGHT);
MyMessage msg15(15, V_LIGHT);
MyMessage msg16(16, V_LIGHT);
MyMessage msg17(17, V_LIGHT);
MyMessage msg18(18, V_LIGHT);
MyMessage msg19(19, V_LIGHT);
MyMessage msg20(20, V_LIGHT);
MyMessage msg21(21, V_LIGHT);
MyMessage msg22(22, V_LIGHT);
MyMessage msg23(23, V_LIGHT);
MyMessage msg24(24, V_LIGHT);
MyMessage msg25(25, V_LIGHT);
MyMessage msg26(26, V_LIGHT);
MyMessage msg27(27, V_LIGHT);
MyMessage msg28(28, V_LIGHT);
MyMessage msg29(29, V_LIGHT);
MyMessage msg30(30, V_LIGHT);
MyMessage msg31(31, V_LIGHT);
MyMessage msg32(32, V_LIGHT);

void loop() {
  // Send locally attached sensor data here
  if (debouncer6.update()) {
    // Get the update value.
    int value6 = debouncer6.read();
    // Send in the new value.
    if (value6 == LOW) {
      saveState(17, !loadState(17));
      digitalWrite(RELAY_17, loadState(17) ? RELAY_ON : RELAY_OFF);
      send(msg17.set(loadState(17)));
    }
  }
  if (debouncer7.update()) {
    int value7 = debouncer7.read();
    if (value7 == LOW) {
      saveState(19, !loadState(19));
      digitalWrite(RELAY_19, loadState(19) ? RELAY_ON : RELAY_OFF);
      send(msg19.set(loadState(19)));
    }
  }
  if (debouncer8.update()) {
    int value8 = debouncer8.read();
    if (value8 == LOW) {
      saveState(21, !loadState(21));
      digitalWrite(RELAY_21, loadState(21) ? RELAY_ON : RELAY_OFF);
      send(msg21.set(loadState(21)));
    }
  }
  if (debouncer9.update()) {
    int value9 = debouncer9.read();
    if (value9 == LOW) {
      saveState(13, !loadState(13));
      digitalWrite(RELAY_13, loadState(13) ? RELAY_ON : RELAY_OFF);
      send(msg13.set(loadState(13)));
    }
  }
  if (debouncer1.update()) {
    int value1 = debouncer1.read();
    if (value1 == HIGH) {
      saveState(3, !loadState(3));
      digitalWrite(RELAY_3, loadState(3) ? RELAY_ON : RELAY_OFF);
      send(msg3.set(loadState(3)));
    }
  }
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type == V_LIGHT) {
  // Change relay state
    digitalWrite(message.sensor - 1 + RELAY_1, message.getBool() ? RELAY_ON : RELAY_OFF);
    // Store state in eeprom
    saveState(message.sensor, message.getBool());
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }
}